2008 997.1 Porsche GT3RS Detail
#1
2008 997.1 Porsche GT3RS Detail
Completed recently, this was a Sharkwerks "Do everything you guys do" build from a 3.9 engine build, roll cage, software, exhaust, suspension, wheels, seats,fywheel, stereo..........................etc. The vehicle was a little rough but came out beautiful as the following pics will demonstrate.
Built for a celebrity in the MMA world who I am a BIG fan of(Read not fanBOY) for his technical prowess, but more important to me his candid honesty and tremendous humor and the fact his feet are still on the ground in the way he interacts with people who are famous fighters/promoters and the common fan.
The beginning after a wash/decon step, carbon wing not looking so hot.
Improvement evident.
15 microns of clear is not much, so I carefully corrected the wing.
50/50 showing entire wing.
The whole wing corrected.
Rear shelf and louvers with marring present.
50/50 on the roof.
50/50 of the clearfilm correction.
Clearfilm on entire trunk lid now corrected.
Water spots and marring on the factory decals, this area can be challenging to correct so the graphic is not ruined while trying to correct the defects.
All better.
Clearfilm on the front bumper was hammered, 50/50 showing the improvement.
Late into the night(This can be the best time in the shop without distractions).
Back over to Sharkwerks to retrieve the new HRE's going on the car, here is UBER tech James who built the car getting things ready for me.
Now before the wheel swap, it was time to clean up the suspension & wheel wells.
Built for a celebrity in the MMA world who I am a BIG fan of(Read not fanBOY) for his technical prowess, but more important to me his candid honesty and tremendous humor and the fact his feet are still on the ground in the way he interacts with people who are famous fighters/promoters and the common fan.
The beginning after a wash/decon step, carbon wing not looking so hot.
Improvement evident.
15 microns of clear is not much, so I carefully corrected the wing.
50/50 showing entire wing.
The whole wing corrected.
Rear shelf and louvers with marring present.
50/50 on the roof.
50/50 of the clearfilm correction.
Clearfilm on entire trunk lid now corrected.
Water spots and marring on the factory decals, this area can be challenging to correct so the graphic is not ruined while trying to correct the defects.
All better.
Clearfilm on the front bumper was hammered, 50/50 showing the improvement.
Late into the night(This can be the best time in the shop without distractions).
Back over to Sharkwerks to retrieve the new HRE's going on the car, here is UBER tech James who built the car getting things ready for me.
Now before the wheel swap, it was time to clean up the suspension & wheel wells.
#2
Time to get the new wheels shaped up.
Wheels cleaned, rubber stripped(But not dressed as they are cup tires).
Wheels were match mounted next door @ Alekshop, witness mark tells the tale.
Factory spec torque settings.
Rollcage.
Carbon shells on the seats.......................so full of winning tightness.
Bigboy audio/laser set up.......................... not for the faint of wallet.
Engine bay standing tall.
Cleaned and more important absent of "Brylcream like dressing", matte finish per new spec.
All finished, waiting to outside for sun pics.
Thread
Thread Starter
Forum
Replies
Last Post
Auto Concierge
Detailing & Paint Protection
2
04-21-2015 04:07 AM
Auto Concierge
Detailing & Paint Protection
3
08-20-2014 08:11 AM
Auto Concierge
Detailing & Paint Protection
4
03-04-2014 07:59 AM
Auto Concierge
Detailing & Paint Protection
2
04-06-2011 10:47 AM
Bookmarks
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)